Phased Manufacture Programme (PMP) for Manufacture of Parts of Mobile Phones and Other Electronic Goods under PMP - Amendments

Rationalization of duties on mobile phone parts for the following- mechanics to 10%, inputs of mechanics to 0% and 'others' to 10%

 

The BCD of 15% on 85177990 was never intended to be 15% —it was raised from 5% in 2018 as part of the PMP architecture. Misinterpretations by field formations led to the standardized.

Mobile phone mfg industry will be more competitive and will face fewer interpretation challenges.

The mechanics change is significant because inputs of mechanics were never intended to be subject to duty in the PMP architecture..therefore this is significant…the arbitrage between inputs and intermediates remains intact - only the final duty has been brought to 10% and all inputs to zero. Industry overall will be more competitive.

 

[Notification No. 09/2024-Customs dated 30 January, 2024]

Seeks to amend Notification No. 57/2017-Customs dated 30.06.2017 so as to change the applicable BCD rate on specified parts/sub-parts of cellular mobile phone

G.S.R. (E).- In exercise of the powers conferred by sub-section (1) of section 25 of the Customs Act, 1962 (52 of 1962), the Central Government, on being satisfied that it is necessary in the public interest so to do, hereby makes the following further amendment in the notification of the Government of India, Ministry of Finance (Department of Revenue), No. 57/2017-Customs, dated the 30th June, 2017, published in the Gazette of India, Extraordinary, Part II, Section 3, Sub-section (i), vide number G.S.R. 798(E), dated the 30th June, 2017, namely:-

In the said notification, in the Table, -

(i)   against S. No. 1, in column (4), for the entry, the entry “10%” shall be substituted;

(ii)  after S. No. 1 and the entries relating thereto, the following S. No. and entries shall be inserted, namely:-

(1)

(2)

(3)

(4)

(5)

“1A

Any Chapter

Inputs or parts for use in manufacture of goods mentioned at S. No. 1 above

Nil

1”;

(iii) after S. No. 6C and the entries relating thereto, the following S. No. and entries shall be inserted, namely:-

(1)

(2)

(3)

(4)

(5)

“6D

39, 73

The following goods for use in manufacture of cellular mobile phones:-

(i)    Battery cover

(ii)   Front cover

(iii)  Middle cover

(iv)  Main lens

(v)   Back cover

(vi)  GSM Antenna/Antenna of any technology

(vii) PU case/Sealing Gasket – Other articles of Polyurethane foam like sealing gaskets/case

(viii)        Sealing Gaskets/ Cases from PE, PP, EPS, PC and all other individual polymers or combination/combinations of polymers

(ix)  SIM socket

(x)   Screw

(xi)  Other mechanical items of plastic

(xii) Other mechanical items of metal

10%

1

6E

Any Chapter

Inputs or parts for use in manufacture of goods mentioned at S. No. 6D above

Nil

1

6F

39

The following goods for use in manufacture of cellular mobile phones:-

(i)    Conductive cloth

(ii)   LCD conductive foam

(iii)  LCD foam

(iv)  BT foam

(v)   Heat dissipation sticker battery cover

(vi)  Sticker-Battery slot

(vii) Protective film for main lens

(viii)        Mylar for LCD FPC

(ix)  Film-front flash

10%

1

6G

Any Chapter

Inputs or parts for use in manufacture of goods mentioned at S. No. 6F above

Nil

1

6H

8538 90 00

Side key for use in manufacture of cellular mobile phones

10%

1

6I

Any Chapter

Inputs or parts for use in manufacture of goods mentioned at S. No. 6H above

Nil

1

6J

8517 79 90

All goods for use in manufacture of cellular mobile phone

10%

1”;

(iv)  against S. No. 7, in column (3), items (viii), (x), (xi), (xxiv), and (xxvi) shall be omitted.

[F.No. CBIC-190354/190/2022-TRU Section-CBEC]